Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
Were you trying to find advise on Installing A Bathtub?
Setting up a bathtub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the job and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will help you set up a new bath tub in your washroom if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also product list must make up the following:
Getting ready for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the tub in the needed placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub till the spirit level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the bath tub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has been made use of a minimum of when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place between the tap and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bathroom and also the tiling, bring about problems with moisture and also feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealer can fracture fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our piece on How to Install a Bathtub Yourself. Thanks for finding the time to read through our short article. Don't hesitate to take a moment to promote this post if you enjoyed it. I praise you for your time. Visit again soon.
Browse Website
Report this page